LEWA metering systems 
for testing of batteries on special test facilities

Drives in electric vehicles require special batteries to meet the automotive sector’s requirements regarding safety, performance, durability, service life, cost and environmental protection. Only specially tested batteries can be used in electric vehicles. Therefore, these batteries run through worst case scenarios in long-term test cycles during extreme operating conditions.

LEWA metering systems have been successfully used in battery test applications for many years. For testing purposes, for example a water-glycol mixture is used. LEWA metering systems guarantee high-precision control of the volume flow and pressure.

Solutions

Metering systems for battery test facilities. Precise control, reproducible test results.

When traction batteries for electric vehicles are tested, extreme operating conditions are simulated. The test cycles vary in length from a few minutes to several hours. LEWA metering systems are used to dose a testing fluid in a closed loop to check the batteries at different temperatures in a wide temperature range.

These LEWA metering systems are divided into different layers: The first consists of a base frame, a drip pan and a cooling water connection. The second includes a tempering unit, metering pumps, measuring instruments and process connections. The third consists of a control cabinet, operating unit, controls and interfaces. By those, the metering systems can be easily connected to customer-side distributed control systems (DCS).

The ratio of the testing fluid is always unchanged, e.g. a water glycol mixture is used. The mixture is adjusted to the desired operating temperature by the tempering unit and then circulated in a closed loop through the batteries. With LEWA metering systems for battery test stands, fluids can be conveyed at temperatures of -30 to 85 °C, at flow rates of 30 to 900 l/h and at a maximum pressure of 10 bar. Metering systems for higher flow rates, temperatures or pressures are available on request.

The actual system components are furnished with thermal insulation. This is indispensable for the systems to prevent that ambient temperatures have an influence on the fluid temperature and its gradients. By this, reproducible results can be achieved. The process parameters volume flow and pressure are controlled symmetrically by the LEWA software in order to ensure reproducibility and stability. The software ensures that the maximum set pressure is never exceeded and does not damage the internal life of the batteries.

Battery testing in pilot plants

Background

Batteries in electric vehicles

In electric vehicles, so-called traction batteries are used. Lithium-ion batteries are the preferred type of traction batteries. In 2014, almost exclusively lithium-ion batteries were installed in electric vehicles.

The batteries are the central and at the same time the most expensive component of an electric vehicle and can add up to about 40% of the total costs. The traction batteries must be able to withstand a variety of charging cycles.

The so-called "memory effect", which is typical for many types of batteries, must not occur. The memory effect describes a loss of capacity of the batteries emerging over time and is characterized by an early voltage drop. As a minimum voltage is required, the battery runtime is sometimes significantly lower.

In the manufacturer's tests, the electric vehicle batteries are subjected to extreme operating conditions (such as high and low temperatures) in test cycles of varying duration. This simulates and examines the influences of the batteries’ aging process.

Industries

LEWA solutions are found also in other industries, for example in the Varnish- and Lacquer industry
LEWA solutions are found also in other industries

Pumps and Metering Systems for Other Industries

LEWA offers customized solutions and references for almost all industries in which processes require exact metering or the reliable conveyance of fluids. As specialists in fluid handling, we of course also have experience in areas outside of our key markets.

More Details

Products

LEWA production units

Customer-Specific Metering, Mixing or Filling Systems from LEWA

Customer-specific batch/continuous systems for your production process. Metering, mixing, filling, separating, controlling temperature: We work with you to develop the ideal process-related sequence and produce the system that fits your production process – right up to the end product.

More Details
LEWA customer specific metering systems

Customer-Specific Metering Systems from LEWA

Turnkey metering system in closed loop control with monitoring and plausibility testing equipment. Your individually configured metering system with an optimally designed pump for fluid metering in automated processes.

More Details

Keep in touch with us

Get insights into our products and applications for liquid metering. You will also receive all the latest news about LEWA as well as invitations to our exclusive events.

Captcha image

Social Media

LEWA is on LinkedinLEWA is on YouTubeLEWA is on Instagram
©2024 LEWA GmbH  Terms & Conditions Privacy Imprint